a EN 10025-6 S620Q strength steel plate
Gangsteel produce and supply materials of EN10025-6 S620q steel plate and equal grade S590Q, S690Q, S690QL, S690QL1, WQ690D, Q550D, WQ590D, WH70Q, WDB620E, WH785E S620q steel plate Executive standard: EN10025-6, GB/T16270-2009.
EN10025-6 S620q Alloy special steel with specified minimum values of impact energy at temperatures not lower than -20 degree .
Chemical composition of steel S620Q (1.8914), Standards of steel S620Q (1.8914) and Mechanical Properties of steel S620Q (1.8914) Equivalent grades of steel S620Q (1.8914)
about the steel S620Q (1.8914) Tensile Strength, Elongation, Proof strength , Hardness, please see our table.
Parent materials as a delivered scenario had a bainitic-martensitic microstructure at hardness about 290 HV0.5. After welding, the microstructure of heat affected zone consists primarily of martensite of hardness 420 HV0.5. It should be famous, nonetheless, that the microstructure of metal in the warmth affected zone varies with the hole from the fusion line. The observed microstructural adjustments had been in accordance with the CCT-S transformation diagram for the examined steel EN10025-6 S620Q steel plate supplier. The results revealed that weld metallic toughness is strongly dependent on the carbon content material of the metal plates, and glorious toughness can be obtained in weld metals with low C contents having an nearly completely decrease bainite construction with out formation of slender martensite austenite constituent .
- What is EN 10025-6 S620Q steel plat?
EN10025-6 S620Q steel plate is EN 1.8914, Alloy special steel with specified minimum values of impact energy at temperatures not lower than -20 ° C. The main adopt standard are EN 10025-6: 2004 Hot rolled products of structural steels. Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10137-2: 1996 S620Q Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions. Delivery conditions for quenched and tempered steels
- What is EN 10025-6 S620Q OR 1.8914 Chemical composition % of steel EN 10025-6 S620Q (1.8914): EN 10025-6-2004
C |
Si |
Mn |
Ni |
P |
S |
Cr |
Mo |
V |
N |
Nb |
Ti |
Cu |
Zr |
B |
CEV |
max 0.2 |
max 0.8 |
max 1.7 |
max 2 |
max 0.025 |
max 0.015 |
max 1.5 |
max 0.7 |
max 0.12 |
max 0.015 |
max 0.06 |
max 0.05 |
max 0.5 |
max 0.15 |
max 0.005 |
max 0.83 |
- What is Mechanical properties of steel EN 10025-6 S620Q (1.8914)?
Nominal thickness (mm): |
3 – 100 |
100 – 150 |
Rm – Tensile strength (MPa) |
700-890 |
650-830 |
- What is Equivalent grades of steel EN10025-6 S620Q (1.8914)
EU |
Germany |
France |
European old |
|||
S620Q |
|
|
|
EN10025-6 EQUAL Grade stock list in China warehouse |
|||||||
|
Grade |
size mm |
Thick mm |
Wide mm |
Long mm |
Tons |
Quantity |
High-strength structural stee plate |
BS960E |
7*1600*11300 |
7 |
1600 |
11300 |
2.023 |
2 |
|
Q550CFD |
16*2500*12000 |
16 |
2500 |
12000 |
3.768 |
1 |
|
Q550CFD |
16*2500*12000 |
16 |
2500 |
12000 |
3.768 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q690CFD |
30*2550*10640 |
30 |
2550 |
10640 |
6.39 |
1 |
|
SC960E |
30*1550*5800 |
30 |
1550 |
5800 |
2.117 |
1 |
|
NQB-S690QL |
20*1700*11000 |
20 |
1700 |
11000 |
2.936 |
1 |
|
BS700MCK2 |
8*1500*13000 |
8 |
1500 |
13000 |
1.227 |
1 |
|
BWELDY620QL6 |
12*2400*6220 |
12 |
2400 |
6220 |
1.406 |
1 |
|
BWELDY620QL6 |
12*2400*9000 |
12 |
2400 |
9000 |
2.035 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.239 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
5.181 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
1.884 |
4 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
2.12 |
1 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
0.707 |
1 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
0.706 |
1 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
2 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
1 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
1 |
|
BS700MCK2 |
12*1500*13000 |
12 |
1500 |
13000 |
1.837 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
1.696 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
4.522 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
4.522 |
1 |
EN 10025-6 S620Q strength steel market
Strenx® is high power structural metal with extraordinarily fixed properties, making it excellent for designing trailer chassis. Shipbuilding requires large portions of structural metal plate to construct to ship hull.
We are Manufacturer and Exporter of S690QL Structural Steel Plate, EN S690QL High Yield Steel Plates Suppliers in Mumbai, India. All of our S690 QL EN 10025–6 structural steel Plates, EN10025 S690QL High Tensile Plate, is made and tried to worldwide tips, and specifications as per ASME, ANSI & ASTM, and so forth. We have our Dealers & Distributors of EN 10025–6 S690 QL Heavy Steel Plates, S690QL structural Steel Plate Unit in Gujarat, Ahmedabad, Pune, Chennai, Indore, Kolkata, Delhi, Nagpur, Bhosari, Bangalore, Punjab, Ludhiana, Gurgaon, Rajkot, Karnataka, Uttar Pradesh, Faridabad, Khopoli, Madhya Pradesh, Jaipur, Ghaziabad, Haryana, Vadodara, West Bengal, Rajasthan, Raipur, Aurangabad, Kolhapur, Chhattisgarh, Tamil Nadu, Karnataka. S355J2WP steel is a hot rolled structural steel with anti-corrosion feature, also referred to as weathering steel and environment corrosion resistance steel, under standard EN . Metallographic examination revealed that the concentrated electron beam significantly affect the modifications of microstructure in the steel.
The code “ L” means that the average minimal values for influence power have been defined at a temperature of -40°C. The code “Q” refers back to the delivery condition, on this case to quenched & Tempered. 09CuPCrNi-A is a weather resistant steel created by alloying copper, chromium and nickel. The material may be heat dealt with using quench and temper techniques. We can observe your drawings and requirements, to give you oxygen chopping, plasma slicing and laser slicing and different processing services.
Alloy steels comprise quite a lot of steels comprising compositions that exceed the limitations of Si, Va, Cr, Ni, Mo, Mn, B and C allotted for carbon steels. In comparability with carbon steels, alloy steels are much more conscious of mechanical and heat cures.
You can even carry out ultrasonic testing in accordance with EN10160 normal, EN10164 normal take a look at Z15, Z25, Z35, weld bending detection, PWHT detection,etc. thanks god, you get our merchandise, Fast suggestions and technology help will make each us carefully. API 5L X65 PSL1 Pipe is a high yield seamless pipe that’s modified to go well with offshore structural functions. It is intended for use in fastened offshore buildings and is designed to function within the offshore sector.
EN 10025-6 S620Q strength steel angle
The metal owes its weathering resistance to the formation of a protective oxide coating which seals the surface against additional corrosion. Our S690Ql is a structural metallic grade and is produced to supply high yield energy throughout utilization. Unitedsteel Mill Supply High power steel plate, and have numerous stock size, If you require high strength steel plate. Unitedsteel Mill Supply High strength steel plate, and have numerous inventory measurement, should you require high energy steel plate, please contact us by way of Email to contact us.
Equivalent grades of steel S620Q (1.8914)Equivalent grades of steel S620Q (1.8914)Heat treatment conditions+A Soft annealed+AC Annealed to achieve spheroidization of the carbides+AR As rolled+AT Solution annealed+C Cold drawn / hard+CR Cold rolled+FP Treated to ferrite-pearlite structure and hardness range+I Isothermal annealing+LC Cold drawn / soft+M Thermo mechanical rolling+N Normalized+NT Normalized and tempered+P Precipitation hardened+PE Peeled+QA Air quenched and tempered+QL Liquid quenched and tempered+QT Quenched and tempered+S Treated to improve shearability+SH As rolled and turned+SR Cold drawn and stress relieved+T Tempered+TH Treated to hardness range+WW Warm worked+U Untreated
Metallurgical properties are investigated through optical and scanning electron microscope. The analysis might be carried out on trendy metal grades by which the phenomena occurring during interactions with excessive-energy beams usually are not completely acknowledged but. We have our own metal pipe manufacturing facility, advanced processing gear and wonderful group. We have in depth experience in exporting, and we now have clients all around the world who purchase steel products from FRD. We have Bs En S690ql structural Steel Plates Stock in varied sizes & dimensions, Contact us for Free quote & pattern of Bs En S690ql High Tensile Plate near you.
- Parent materials as a delivered scenario had a bainitic-martensitic microstructure at hardness about 290 HV0.5.
- The outcomes revealed that weld metallic toughness is strongly depending on the carbon content material of the metal plates, and wonderful toughness could be obtained in weld metals with low C contents having an nearly absolutely lower bainite construction with out formation of slender martensite austenite constituent .
- After welding, the microstructure of warmth affected zone consists primarily of martensite of hardness 420 HV0.5.
- The outcomes indicated that a single-sided welding approach might be used to affix S690QL steels as much as a thickness of 12 mm when the laser energy is the same as 12 kW (scan speed 1 m/min).
- It must be noted, nonetheless, that the microstructure of metallic within the heat affected zone varies with the hole from the fusion line.
3. Implementation standards: national standards, metallurgical standards, American ASME, ASTM, Japanese JIS, German DIN, French NF, British BS, European EN, international ISL standards, etc.
4. Production grade; A/B/C/D/E and thickness direction performance Z15 Z25 35.
The outcomes indicated that a single-sided welding method could be used to affix S690QL steels as much as a thickness of 12 mm when the laser energy is the same as 12 kW (scan speed 1 m/min). Double-aspect welding method allows larger weld penetration and better management of warmth distribution. Observation of the samples showed that the fusion zone exhibited bainitic and martensitic microstructures with elevated quantities of martensites compared with the bottom provides. Also, the grains within the fusion zone elevated in coarseness as the warmth enter was elevated. 16Mo3 Steel is a EN10028 specified pressure vessel grade chrome molybdenum steel alloy is used as a weldable steel within the fabrication of industrial boilers and metal pressurised vessels found in the oil. Mechanical and metallurgical properties of electron beam welded joint of SAE 5137H had been evaluated. Mechanical properties are analysed by tensile, influence and hardness take a look at.