EN10025-6 S620Q steel channel
Gangsteel produce and supply materials of EN10025-6 S620q steel plate and equal grade S590Q, S690Q, S690QL, S690QL1, WQ690D, Q550D, WQ590D, WH70Q, WDB620E, WH785E S620q steel plate Executive standard: EN10025-6, GB/T16270-2009.
EN10025-6 S620q Alloy special steel with specified minimum values of impact energy at temperatures not lower than -20 degree .
Chemical composition of steel S620Q (1.8914), Standards of steel S620Q (1.8914) and Mechanical Properties of steel S620Q (1.8914) Equivalent grades of steel S620Q (1.8914)
about the steel S620Q (1.8914) Tensile Strength, Elongation, Proof strength , Hardness, please see our table.
EN10025-6 S620Q steel round bar
Minimise the shrinkage stress by guaranteeing an excellent match and a nicely planned sequence of weld runs. Process G reveals TM-rolling adopted by direct quenching and self tempering.
Information about metal pipe and becoming codes, industrial requirements of pipe fittings, pipe fitting standards, ASTM standards, DIN requirements, JIS & GB standards. We are committed to deliver a total solution of steel pipes, fittings, flanges logistics and technical companies to satisfy our shopper’s requirements in probably the most efficient and cost efficient method. Sunny Steel present a wide range of metal merchandise as Steel pipes, Seamless tube and seamless pipes, Alloy pipes, Pipe fittings, Composite steel pipe used within the business, development etc. We promote a wide variety of metals including Hot-Rolled Steel, Cold-Rolled Steel, Stainless Steel, Alloy Steel, Galvanized Steel Pipe and Oil Tanks. Our common practical expertise is that post weld heat therapy just isn’t necessary. The toughness and hardness of the weldment normally meet the necessities and isn’t substantially improved by stress relieving. It should solely be carried out if a discount of the residual stresses is required for some special function or if specified in the design codes.
- What is EN 10025-6 S620Q steel plat?
EN10025-6 S620Q steel plate is EN 1.8914, Alloy special steel with specified minimum values of impact energy at temperatures not lower than -20 ° C. The main adopt standard are EN 10025-6: 2004 Hot rolled products of structural steels. Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10137-2: 1996 S620Q Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions. Delivery conditions for quenched and tempered steels
- What is EN 10025-6 S620Q OR 1.8914 Chemical composition % of steel EN 10025-6 S620Q (1.8914): EN 10025-6-2004
C |
Si |
Mn |
Ni |
P |
S |
Cr |
Mo |
V |
N |
Nb |
Ti |
Cu |
Zr |
B |
CEV |
max 0.2 |
max 0.8 |
max 1.7 |
max 2 |
max 0.025 |
max 0.015 |
max 1.5 |
max 0.7 |
max 0.12 |
max 0.015 |
max 0.06 |
max 0.05 |
max 0.5 |
max 0.15 |
max 0.005 |
max 0.83 |
- What is Mechanical properties of steel EN 10025-6 S620Q (1.8914)?
Nominal thickness (mm): |
3 – 100 |
100 – 150 |
Rm – Tensile strength (MPa) |
700-890 |
650-830 |
- What is Equivalent grades of steel EN10025-6 S620Q (1.8914)
EU |
Germany |
France |
European old |
|||
S620Q |
|
|
|
EN10025-6 EQUAL Grade stock list in China warehouse |
|||||||
|
Grade |
size mm |
Thick mm |
Wide mm |
Long mm |
Tons |
Quantity |
High-strength structural stee plate |
BS960E |
7*1600*11300 |
7 |
1600 |
11300 |
2.023 |
2 |
|
Q550CFD |
16*2500*12000 |
16 |
2500 |
12000 |
3.768 |
1 |
|
Q550CFD |
16*2500*12000 |
16 |
2500 |
12000 |
3.768 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
20*2500*12000 |
20 |
2500 |
12000 |
4.71 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q550CFD |
36*2500*9500 |
36 |
2500 |
9500 |
6.712 |
1 |
|
Q690CFD |
30*2550*10640 |
30 |
2550 |
10640 |
6.39 |
1 |
|
SC960E |
30*1550*5800 |
30 |
1550 |
5800 |
2.117 |
1 |
|
NQB-S690QL |
20*1700*11000 |
20 |
1700 |
11000 |
2.936 |
1 |
|
BS700MCK2 |
8*1500*13000 |
8 |
1500 |
13000 |
1.227 |
1 |
|
BWELDY620QL6 |
12*2400*6220 |
12 |
2400 |
6220 |
1.406 |
1 |
|
BWELDY620QL6 |
12*2400*9000 |
12 |
2400 |
9000 |
2.035 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.239 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
5.181 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
4.71 |
1 |
|
BS700MCK2 |
10*1500*4000 |
10 |
1500 |
4000 |
1.884 |
4 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
2.12 |
1 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
0.707 |
1 |
|
BS700MCK2 |
10*1500*6000 |
10 |
1500 |
6000 |
0.706 |
1 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
2 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
1 |
|
BS700MCK2 |
12*1500*12000 |
12 |
1500 |
12000 |
3.391 |
1 |
|
BS700MCK2 |
12*1500*13000 |
12 |
1500 |
13000 |
1.837 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
1.696 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
4.522 |
1 |
|
BS700MCK2 |
12*1500*4000 |
12 |
1500 |
4000 |
4.522 |
1 |
High-strength metal delivered in a thermomechanically rolled condition is manufactured in accordance with EN , DSTU EN and EN , as well as different regulatory paperwork and underneath personal brands of producers. EQUIMETALS can also offer you close equal and similar steels from totally different international locations, and provide you a listing of the commonest use case situations. EQUIMETALS can provide actual chemical composition, mechanical properties in several states, warmth treatment procedures for numerous functions, in addition to detailed corrosion data for over 70 corrosive mediums in a number of mixtures of focus and temperature. The MSZ S 620 Q MSZ EN material bodily properties shall comply with the values given within the following desk. The TM steels have a wider window for heat input and preheating than QT steels. Even for thicker plates of S460M preheating could be omitted and thus welding prices lowered. The pressure redistribution was analysed and confirmed a wonderful settlement between simulation and check.
EN 10025-6 S620Q strength steel note
With the verified mannequin, additional calculations have been carried out to analysis the influence of varied materials mixtures of base and filler metals. Figure 23 illustrates the numerical outcomes of two completely different materials mixtures. It can be seen that, by increasing the energy of the filler steel from G46 to G69, the load bearing capability will increase nearly in the same means, impartial of the base metallic power. Therefore, an increase throughout the energy of the underside metal does not necessarily result in the next load bearing capability, within the case failure occurs throughout the weld.
EN 10025-6 S620Q strength steel grades currently used in north america
Equivalent grades of steel S620Q (1.8914)Equivalent grades of steel S620Q (1.8914)Heat treatment conditions+A Soft annealed+AC Annealed to achieve spheroidization of the carbides+AR As rolled+AT Solution annealed+C Cold drawn / hard+CR Cold rolled+FP Treated to ferrite-pearlite structure and hardness range+I Isothermal annealing+LC Cold drawn / soft+M Thermo mechanical rolling+N Normalized+NT Normalized and tempered+P Precipitation hardened+PE Peeled+QA Air quenched and tempered+QL Liquid quenched and tempered+QT Quenched and tempered+S Treated to improve shearability+SH As rolled and turned+SR Cold drawn and stress relieved+T Tempered+TH Treated to hardness range+WW Warm worked+U Untreated
en10025-6 S620q steel plate technical parameters
Similar materials of S620q steel plate: S590Q, S690Q, S690QL, S690QL1, WQ690D, Q550D, WQ590D, WH70Q, WDB620E, WH785E S620q steel plate Executive standard: EN10025-6, GB/T16270-2009
S620q steel plate chemical elements: Cu Mo Nb Ni Ti V Zr ≤0.50≤0.70≤0.06≤2.0≤0.05≤0.12≤0.15
Mechanical properties of S690Q steel plate: Yield strength σ0.2 (MPa) Tensile strength σb ( MPa) Elongation (δ5 %) -20��V type impact energy (longitudinal) 590-650 770-940 ≥14≥30
��Specification range: thickness 8-350mm width 1500-4020mm length 3000mm-18800mm.
EN metal grade specification is a high yield power structural steels within the quenched and tempered condition metal plate grade in S500QL, S500QL1, S460Q, S460QL, S460QL1, S620QL1, S550Q, S550QL, S550QL1, S500Q, S890QL1, S960Q, S960QL, S620Q, S620QL, S690Q, S690QL, S690QL1, S890Q and S890QL steel plate grade. S620Q S620QL and S620QL1 high yield energy structural steels grade within the quenched and tempered and S620Q/ QL/ QL1 steel plate might be used in Mechanical Engineering,suspensi on arm and others parts in machine. EN S960Q steel plates are underneath normal BS EN , as same as S460Q/S460QL/S460QL1, S500Q/S500QL/S500QL1, S550Q/S550QL/S550QL1, S620Q/S620QL/S620QL1, S690Q/S690QL/S690QL1, S890Q/S890QL/S890QL1, S960QL and S960QL1.
The steels treated right here have low contents of alloying parts and low carbon equivalents. They may be simply welded to all strange structural steels utilizing any conventional arc welding method. This is very true for the TM steels since an S460M metal has a decrease carbon equal than an ordinary structural steel. The TM steels have a wider window for heat input and preheating than QT steels. Even for thicker plates of S460M preheating could be omitted and thus welding costs reduced. Even the shipbuilding industry has began to design with excessive strength steel.
Further rolling passes are accurately outlined at a temperature under the recrystallisation temperature and generally even in the temperature vary of coexisting austenite and ferrite / pearlite . The process could also be finished by an accelerated cooling especially for thicker plates . The thermomechanical controlled course of (rolling; TMCP) requires meticulous control of the plate temperature and deformation during rolling.
- Even for thicker plates of S460M preheating could be omitted and thus welding costs reduced.
- The TM steels have a wider window for heat enter and preheating than QT steels.
- This is especially true for the TM steels since an S460M steel has a lower carbon equivalent than an strange structural metal.
Properties obtained after TMCP can’t be accomplished by normalising or different kinds of warmth treatment. The last fantastic-grained microstructure of metal is obtained by micro-alloying, rolling in a sure temperature range and managed cooling (as well as accelerated cooling using an air-water combine). High-strength metal permits for significantly longer service life of apparatus and machines, less frequent replacement and repairs of equipment, and less downtime. We are reliable as a result of we know the market, we are sincere, truthful and we’ll meet our promise to our purchasers. We provide our clients with the most effective worth products in an effort to grow their reputation inside their business.
Sunny Steel prides itself on the professional relationship we develop with all shoppers EN10025-6 S620Q steel plate supplier.